Saturday, September 23, 2017

How To Install A Draw Curtain Rod

November 30, 2010 by  
Filed under Drapery Hardware, How To Install

In this article I will review the installation of a conventional traversing curtain rod or commonly know as a draw rod. Make sure you have your curtains, good tape measure, wall anchors and drapery pins and a curtain rod.   

First…determine your face width. For a split draw curtain rod measure the width of both panels add the two together and subtract 12 inches. This is your face width, so if you added both panels to be 90 then your face width is 78. The 12 inches accounts for 2-4 inches returns at each end and center overlap. OK now you have your face width lets say its 78, then you center that 78 inches over your window. This is the width your going to put your brackets. Note: for a one way draw curtain rod only subtract 4 inches because you will have only one return. So in this example you would subtract 4 from 90 to get 86 inches. Then 86 will be your face width.
  
Second…determine your height. Measure the length of your drapes and then decide how high off the floor you would like them. Let say you want them 1/2 off the floor. So you take your length of panels 85 inches for example and add 1/4 inch for a total height of 85 1/4 inch. This will be the height from the floor to the top of your bracket. I’ll explain the 1/4 inch in the step four below. Remember if you have an uneven floor make sure you take that into consideration. 

  

Third…mount your brackets. Use 1 3/4 to 2 inch screws. This should be long enough so if you do hit a wood beam your screw will go into it. If you don’t hit any beams then use a good fastener like toggles. Don’t use plastic anchors, they’re not strong enough and will pull out.   

Fourth…count your carriers. When you install your drapes two pins will go into the lead carriers and 2 into each return all remaining pins will slip into the little plastic carriers that slide back and forth in the rod. Make sure you match the number of pins to the number of carriers. For example if you have 25 pins on one panel, 2 will clip into the lead carrier and 2 into the return that leaves 21, so you should have 21 plastic carriers in the rod for each panel. Remove any excess carriers as they will result in the curtains not closing fully.   

Fifth…pin your curtains. Pin your curtains so the top of the pin is 1/4 inch below the top the header. The final result will be the panels 1/2 inch off the floor. You can move the pin up or down on the curtain to play with the height off the floor.   

Sixth…this is a very important step. Once the rod is installed, you’ll see you have plastic carriers for the pins to hook into and then you have the lead or master carrier. That is the bigger metal piece that you see the string attached to on the back. On the back of the master carrier you see a finger sticking down with a cord just above it. Now draw the rod closed so the carriers meet in the middle. For a one way draw, draw it closed to one side. Hold the carriers in place and with a pair of long nose pliers grab the cord and catch it around the finger pointing down. You’ll see this step in the instructions. Failure to do this will result in the curtain rod not opening and closing properly.   

Each curtain comes packaged with all hardware needed and installation instructions. I suggest buying your own screws and anchors, the size I recommended above. Let me know how it goes or better yet send me a pic…. Good luck.….more info
 

  

For More Info Click Here  

    

Have Questions Then ASK THE EXPERT   

Related Articles
The Number ONE Problem With Panel Track Blinds
Window treatments for Bay Windows…What you need to know before you buy
Energy Efficient Blinds…My Favorite Choice
How to save money on faux wood 2 inch blinds
It’s midnight anytime you want with these cellular shades
Latest thing in window treatments for sliding doors
Roll up shades…operate effortlessly with this latest feature
Your Must Know Guide To Window Treatments
Everything You Need To Know About Verticals
Wood Blinds vs Faux Wood Blinds…and the winner is
Questions You Must Ask Before Buying Interior Shutters
Secrets Of Successful Draperies   

Comments

2 Responses to “How To Install A Draw Curtain Rod”
  1. Sharon Davis says:

    Hi

    I never work a Traverse rod this is my first time so I have lot of Question Do you have any video that shown me step by step on installing my rod online? I am putting a cornice over the rod How much off should I put my cornice? Here is some example to work with I am doing a window width of 48″,40″134″,133″ and 117″ Cornice and Pinch pleast to go on the traverse rod? What would be my projection for the Cornice? My panels lenght is 85″. my cornice length is 14″

  2. Robert says:

    Hi Sharon
    I don’t have a video for traverse rod installations and couldn’t find one online. I did find detailed installation instructions for traverse rods, there is a link below. The projection of your cornice depends on the projection of your drapes. Do you plan on using sheers and drapes or just drapes? Is there any protrusion such as a sill that the drapes have to clear? If your just doing drapes without sheers and don’t have to clear any sills then 5 1/2 projection on your cornice might be ok. If your using both sheers and drapes the 7 1/2 projection might be fine. Are these being custom made , home made or bought out of stock?

    installations instructions for traverse

Speak Your Mind

Tell us what you're thinking...
and oh, if you want a pic to show with your comment, go get a gravatar!